Search found 19 matches

by ndmccutcheon
Wed Jul 31, 2019 7:40 pm
Forum: Ninebot ES
Topic: What size tamper proof Allen wrench for external battery?
Replies: 7
Views: 602

Re: What size tamper proof Allen wrench for external battery?

I haven't seen anything used other than size 3 tamperproof hex screws. Some security bit sets have it, the bit's usually just *barely* long enough for a driver to grab onto it.
by ndmccutcheon
Fri Jul 12, 2019 3:24 pm
Forum: Ninebot ES
Topic: Ninebot MAX custom Firmware
Replies: 1
Views: 1016

Re: Ninebot MAX custom Firmware

This is pure speculation, but the new Bird One scooters look like modified MAX scooters, so hopefully parts and flashing tools will eventually pop up. I know for sure that the new Lyft scooters coming out soon are MAX-based.
by ndmccutcheon
Sun Jun 23, 2019 1:48 pm
Forum: Ninebot ES
Topic: Are all Bird ES4s error 10 on dash replacement?
Replies: 7
Views: 1132

Re: Are all Bird ES4s error 10 on dash replacement?

The most recent wave of bird ES4’s (with battery cages) I believe all give error 10. I’m sorry you’re having trouble with soldering, it definitely is tough to do such small operations. But, unfortunately it’s necessary if you want to get rid of the error without replacing the control board :( you co...
by ndmccutcheon
Sun Jun 23, 2019 6:36 am
Forum: Ninebot ES
Topic: Alternative throttle algorithm
Replies: 2
Views: 745

Re: Alternative throttle algorithm

I believe the normal algorithm is speed-based (imagine altering the set speed on a car’s cruise control) and the alt algorithm is power-based (imagine changing how much you press the gas pedal).
by ndmccutcheon
Mon Jun 10, 2019 4:24 pm
Forum: Ninebot ES
Topic: ES4 Error 10
Replies: 76
Views: 16372

Re: ES4 Error 10

I successfully flashed a controller and then went to connect and got the Error 10 message. I came to this thread and figured i need to flash the control board in the tube as well. I have two brand new bird ES4s. I cannot for the live of me get the damn wires to stick to the control board. any sugge...
by ndmccutcheon
Wed Jun 05, 2019 3:48 am
Forum: Ninebot ES
Topic: How to flash your Ninebot Scooter
Replies: 110
Views: 60475

Re: How to flash your Ninebot Scooter

https://cdn.discordapp.com/attachments/569701483235508224/571906908596731944/unknown.png I followed the guide exactly and im getting this error. Connections and soldering are good Hello, I have exactly the same problem when flashing a dash from Aliexpress. I need to flash this dash because it does ...
by ndmccutcheon
Mon Jun 03, 2019 9:01 pm
Forum: Ninebot ES
Topic: ES4 Error 10
Replies: 76
Views: 16372

Re: ES4 Error 10

I'd like to add that I have flashed two ESCs with ST-Utility and full dump. The scooter works as intended, however disco lighting has stopped working as mentioned above. The method I used: Connect ST-Link to ESC In STUtility press control B and disable readout protection Open full bin Press CTRL+P ...
by ndmccutcheon
Sat Jun 01, 2019 10:56 am
Forum: Ninebot ES
Topic: ES4 Error 10
Replies: 76
Views: 16372

Re: ES4 Error 10

The schematic you found is indeed correct and it's the same one I use ;) There's nothing special to know, just solder and flash. TVCC is indeed 3.3V. As for the flashing part, fulldump refers to a fulldump file of the DRV (bootloader + firmware + user settings), and you can flash it with OpenOCD or...
by ndmccutcheon
Fri May 31, 2019 10:23 am
Forum: Ninebot ES
Topic: CFW Generator not working
Replies: 9
Views: 819

Re: CFW Generator not working

I’m getting this too.
by ndmccutcheon
Fri May 31, 2019 12:28 am
Forum: Ninebot ES
Topic: ES4 Error 10
Replies: 76
Views: 16372

Re: ES4 Error 10

Flash ESC with fulldump using an ST Link. Do some research, and you'll find the method :) Would you be able to elaborate on where to find this info? I've been searching but haven't found anything of use other than this wiring diagram: https://imgur.com/a/heG6ETh showing where to solder each pin. Is...

Go to advanced search