ScooterHacking ReFlasher - ESC recovery/downgrade
Re: ScooterHacking ReFlasher - ESC recovery/downgrade
Hello, is it possible to somehow flash DRV on ninebot d18?
Re: ScooterHacking ReFlasher - ESC recovery/downgrade
I solved the problem myself, thanks for your attention!
Re: ScooterHacking ReFlasher - ESC recovery/downgrade
Hello
i made this first time so i can not conekt to Target
I have made all right bud no conection
[ReFlasher] Starting..
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
Info : clock speed 450 kHz
Info : STLINK V2J34S7 (API v2) VID:PID 0483:3748
[ReFlasher] Found ST-Link
Info : Target voltage: 3.270400
Error: init mode failed (unable to connect to the target)
[ReFlasher] Couldn't connect to target
What can i do
i use the board from the pic
The LED´s blink grean and one red LED is on
i hope for help
i made this first time so i can not conekt to Target
I have made all right bud no conection
[ReFlasher] Starting..
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
Info : clock speed 450 kHz
Info : STLINK V2J34S7 (API v2) VID:PID 0483:3748
[ReFlasher] Found ST-Link
Info : Target voltage: 3.270400
Error: init mode failed (unable to connect to the target)
[ReFlasher] Couldn't connect to target
What can i do
i use the board from the pic
The LED´s blink grean and one red LED is on
i hope for help
Re: ScooterHacking ReFlasher - ESC recovery/downgrade
I have use zadig-2.8 for the USB Connection
bud ther is one Mistake
Se Pic Below
Is this the reason ?
No WCID on USB
bud ther is one Mistake
Se Pic Below
Is this the reason ?
No WCID on USB
Re: ScooterHacking ReFlasher - ESC recovery/downgrade
Hello
i made this first time so i can not conekt to Target
I have made all right bud no conection
[ReFlasher] Starting..
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
Info : clock speed 450 kHz
Info : STLINK V2J34S7 (API v2) VID:PID 0483:3748
[ReFlasher] Found ST-Link
Info : Target voltage: 3.270400
Error: init mode failed (unable to connect to the target)
[ReFlasher] Couldn't connect to target
What can i do
i use the board from the pic
The LED´s blink grean and one red LED is on
i hope for help
hey i had the same error.
STM32 ST-LINK Utility v4.6.0 is very likely what you are missing with this tool update the stick without having anything connected after that everything should work as described
Read the instructions that solved my problem.
https://rollerplausch.com/threads/st-li ... ring.4270/
Re: ScooterHacking ReFlasher - ESC recovery/downgrade
Hello!
Just wanted to give a small comment to the discussion. So it happened that I've encountered this thread when trying to flash the controller on my Ninebot Max G30LP. I've discovered an error in the flasher documentation. It appears that in the images provided as the guide to connecting the wires, the SWDIO and SWCLK are shown incorrectly.
As a more general comment - the controller for G30D and G30LP seem to be identical, minus one of the white connectors. The correct connection schema is provided here: https://rollerplausch.com/threads/st-li ... llen.4270/
Please update the flasher documentation (the image for G30D), since it can be quite confusing.
Also please add a separate image for the G30LP scooters.
Just wanted to give a small comment to the discussion. So it happened that I've encountered this thread when trying to flash the controller on my Ninebot Max G30LP. I've discovered an error in the flasher documentation. It appears that in the images provided as the guide to connecting the wires, the SWDIO and SWCLK are shown incorrectly.
As a more general comment - the controller for G30D and G30LP seem to be identical, minus one of the white connectors. The correct connection schema is provided here: https://rollerplausch.com/threads/st-li ... llen.4270/
Please update the flasher documentation (the image for G30D), since it can be quite confusing.
Also please add a separate image for the G30LP scooters.
- itsrosey22
- Posts: 1
- Joined: Mon Apr 15, 2024 1:16 am
Re: ScooterHacking ReFlasher - ESC recovery/downgrade
Warn : Cannot identify target as a STM32 family.
Does anybody know how to fix??
Does anybody know how to fix??
Re: ScooterHacking ReFlasher - ESC recovery/downgrade
Can you share a photo of the controller and how you connected the ST-Link?Warn : Cannot identify target as a STM32 family.
Does anybody know how to fix??
Who is online
Users browsing this forum: Bing [Bot] and 1 guest