I have flashed SHFW 0.2.5 to my Xiaomi Pro 2.
The flashing process finishes successfully and everything seems to work, I can tune the SHFW config, turn on/off lights, change the User Interface Idle screen, etc...
But the throttle lever doesn't work, and the scooter cannot throttle in any of the modes.
I can flash back again to the original FW or CFW and throttle lever works again, but I have not been able to throttle with SHFW in any way.
Am I doing something wrong? Have someone experienced the same problem?
Xiaomi Pro 2 throttle lever doesn't work with SHFW 0.2.5
Re: Xiaomi Pro 2 throttle lever doesn't work with SHFW 0.2.5
Have you configured your power curves? Obviously, the scooter won't move if you don't set power parameters, SHFW doesn't come with any out of the box.I have flashed SHFW 0.2.5 to my Xiaomi Pro 2.
But the throttle lever doesn't work, and the scooter cannot throttle in any of the modes.
Re: Xiaomi Pro 2 throttle lever doesn't work with SHFW 0.2.5
OMG. That was the problem!Have you configured your power curves? Obviously, the scooter won't move if you don't set power parameters, SHFW doesn't come with any out of the box.I have flashed SHFW 0.2.5 to my Xiaomi Pro 2.
But the throttle lever doesn't work, and the scooter cannot throttle in any of the modes.
It was so obvious I didn't realize.
I assumed it was coming with some predefined power parameters like other firmwares and just checked throttling after flashing and I though there was some problem.
Thanks a lot :)
- penny14036
- Posts: 6
- Joined: Tue Aug 23, 2022 1:21 am
Re: Xiaomi Pro 2 throttle lever doesn't work with SHFW 0.2.5
I also think you should completely follow the instructions. Remember to pay attention to a few small steps on the wheel part.
- allbertluu
- Posts: 1
- Joined: Thu Aug 25, 2022 7:09 am
Re: Xiaomi Pro 2 throttle lever doesn't work with SHFW 0.2.5
In addition to these two new features, SHFW 0.2.5 also fixes a problem where the screen would not turn on when the battery is low and adds a new option to calibrate the resistance range of your coil.
cinenerdle stumble guys
cinenerdle stumble guys
Re: Xiaomi Pro 2 throttle lever doesn't work with SHFW 0.2.5
This is a serious issue, as it means that users who are using this device will not be able to use it with any other SHFW app, and it means that they will have to manually adjust the throttle lever in order to use the device. wordle nyt
Re: Xiaomi Pro 2 throttle lever doesn't work with SHFW 0.2.5
I followed all the instruction but it still doesn't work. This is a severe problem because it prevents users from using the device with any other SHFW apps and forces them to manually adjust the throttle lever in order to operate the deviceFollow the instructions and remember to pay attention to a few small steps casino utan omsättningskrav här
- Henrivonsteen
- Posts: 5
- Joined: Sun Sep 18, 2022 12:44 pm
Re: Xiaomi Pro 2 throttle lever doesn't work with SHFW 0.2.5
Hi there.
Have you adjusted your throttle curve? Connect your shu app and wait a few seconds. The head to config to adjust your throttle curve. If not it won't work.( I tried my best to get a linear setting adjusting the curve, but the trottle would be max when I touch the trottle. In the end I reverted back to speed base setting.) At least my scooter is going. Now my max speed is only 29. Before the flash I managed 31?
Have you adjusted your throttle curve? Connect your shu app and wait a few seconds. The head to config to adjust your throttle curve. If not it won't work.( I tried my best to get a linear setting adjusting the curve, but the trottle would be max when I touch the trottle. In the end I reverted back to speed base setting.) At least my scooter is going. Now my max speed is only 29. Before the flash I managed 31?
Who is online
Users browsing this forum: No registered users and 8 guests