Max dashboard BLE555 ST-Link guide (flash CFW)

Mr Green
Posts: 5
Joined: Fri Dec 13, 2019 10:37 pm

Re: Max dashboard BLE555 ST-Link guide (flash CFW)

Postby Mr Green Fri Jan 03, 2020 3:17 pm

Where is the C2 located on the G30D dashboard?
rex72727
Posts: 7
Joined: Sun Jan 19, 2020 2:09 am

Re: Max dashboard BLE555 ST-Link guide (flash CFW)

Postby rex72727 Mon Jan 20, 2020 11:20 pm

I'm trying this on a Spin but I cannot get the bottom wires to disconnect - near the on/off button. They go into a black sleeve and they don't budge.

The instructions say I can flash with the dash still on, I have the 3 wire sets disconnected from the top of the dash display - should I put those back on before flashing? I'm currently doing all this while it is flashing 32 over and over and over as it has for days.

Thansk!
rex72727
Posts: 7
Joined: Sun Jan 19, 2020 2:09 am

Re: Max dashboard BLE555 ST-Link guide (flash CFW)

Postby rex72727 Tue Jan 21, 2020 11:37 pm

So I got C2 off cleanly. I connected the 3 wires as instructed - mind you mine is beeping with error 32 which I'm still trying to figure out means this can still be done - and I get this error:

"===================================================
Ninebot Max Dashboard Flasher - ScooterHacking.org
===================================================
Waiting for flash to start...

Waiting for 0 seconds, press a key to continue ...
Flashing BLE555 Max firmware
Open On-Chip Debugger 0.10.0 (2019-02-10) [https://github.com/sysprogs/openocd]
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
WARNING: interface/stlink-v2.cfg is deprecated, please switch to interface/stlink.cfg
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter speed: 1000 kHz
Info : clock speed 1000 kHz
Info : STLINK V2J29S7 (API v2) VID:PID 0483:3748
Info : Target voltage: 3.170428
Error: init mode failed (unable to connect to the target)


Done! Check the logs to verify if the flash was successful.
Press any key to continue . . ."

Cany anyone help?
kiki626
Posts: 7
Joined: Mon Jun 24, 2019 6:01 am

Re: Max dashboard BLE555 ST-Link guide (flash CFW)

Postby kiki626 Wed Jan 22, 2020 9:05 pm

So I got C2 off cleanly. I connected the 3 wires as instructed - mind you mine is beeping with error 32 which I'm still trying to figure out means this can still be done - and I get this error:

"===================================================
Ninebot Max Dashboard Flasher - ScooterHacking.org
===================================================
Waiting for flash to start...

Waiting for 0 seconds, press a key to continue ...
Flashing BLE555 Max firmware
Open On-Chip Debugger 0.10.0 (2019-02-10) [https://github.com/sysprogs/openocd]
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
WARNING: interface/stlink-v2.cfg is deprecated, please switch to interface/stlink.cfg
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter speed: 1000 kHz
Info : clock speed 1000 kHz
Info : STLINK V2J29S7 (API v2) VID:PID 0483:3748
Info : Target voltage: 3.170428
Error: init mode failed (unable to connect to the target)


Done! Check the logs to verify if the flash was successful.
Press any key to continue . . ."

Cany anyone help?

Its saying can't connect to target check your soldering and make sure you're connected to the correct wires. Pull the cover off your STLink and make sure the wires match up sometimes the label on the cover is wrong.
rex72727
Posts: 7
Joined: Sun Jan 19, 2020 2:09 am

Re: Max dashboard BLE555 ST-Link guide (flash CFW)

Postby rex72727 Wed Jan 22, 2020 10:42 pm

It looks like mine was labeled correctly. The bottom right pin is SWDIO, then to the left also on the bottom is ground, then after that is SWCLK.

I double checked to make the sure the drivers were installed on Windows 10 and they are.


I just want to confirm - has anyone successfully flashed a Spin that was actively beeping an error 32 on the dash while they flashed?
sc00tr
Posts: 12
Joined: Tue Jul 09, 2019 4:35 pm

Re: Max dashboard BLE555 ST-Link guide (flash CFW)

Postby sc00tr Fri Jan 24, 2020 10:07 pm

Yes Rex, the error doesn’t mean much for flashing other than that the scooter is irritating. It can still be flashed.
Acal2019
Posts: 1
Joined: Mon Feb 10, 2020 4:25 pm

Re: Max dashboard BLE555 ST-Link guide (flash CFW)

Postby Acal2019 Mon Feb 10, 2020 4:33 pm

Hello 👋
I have never flashed a max spin scooter Before .
So I am very new, I joined the community too see the difficulty of flashing is an tbh I’m still confused. Idk where to download the files an I don’t know what computer can download them I have Mac book air running OSX El Capitan an I do have a windows 7 desktop computer
What machine you recommend I use to download the files to run the flash ?

An one other question I have a wire that I made that can connect straight to the Iot cord that Lies behind the Iot an it fits but do I still need to any soldering to the dashboard?

One end of the cord is Usb an the other end connects to the cord the Iot connects too.



If some one can help me with this that would be great an I can send you a picture of the cord I have an you can tell me if it will work.

Thank you once again .
BotMinh
Posts: 1
Joined: Wed Feb 19, 2020 4:44 pm

Re: Max dashboard BLE555 ST-Link guide (flash CFW)

Postby BotMinh Wed Feb 19, 2020 4:51 pm

Hello everyone,
rex72727 i have the same problem ( Error: init mode failed (unable to connect to the target)), is there someone who know how to solve it ?
I need to flash the dashboard with BLE555 using St-Link just to put a new CFW on a ex-rental scooter .

thanks you a lot
User avatar
Unicycle Santa
Posts: 15
Joined: Sat Feb 22, 2020 9:42 pm

Re: Max dashboard BLE555 ST-Link guide (flash CFW)

Postby Unicycle Santa Sat Feb 29, 2020 2:51 am

Just wanted to add some experience here. I just did this with an M365 Pro dash as well as a Ninebot Max dash from aliexpress and it worked on both. I will be posting a comprehensive tutorial on how to get one of these scooters working including BMS flash, dash flash, ESC flash, and using Ninebot Flasher to get things working with a custom firmware.
lewy10
Posts: 3
Joined: Tue Feb 04, 2020 6:23 am

Re: Max dashboard BLE555 ST-Link guide (flash CFW)

Postby lewy10 Sat Feb 29, 2020 9:57 pm

Just wanted to add some experience here. I just did this with an M365 Pro dash as well as a Ninebot Max dash from aliexpress and it worked on both. I will be posting a comprehensive tutorial on how to get one of these scooters working including BMS flash, dash flash, ESC flash, and using Ninebot Flasher to get things working with a custom firmware.
Please post that tutorial. Im just banging head on the wall trying to get my Max G30 up and running again. Sucks error code 19.

Return to “Ninebot KS Max”

Who is online

Users browsing this forum: No registered users and 1 guest