[Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
Re: [Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
I am now having a problem with the power buttons, I have two converted lyfts one with a clone dash one without, one ble555 and the other 113, button on ble does nothing on either scooter.. Anyway to fix this?
Re: [Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
I was able to flash the dash but for some reason i cant seem to connect to the bms it says check swim cable and pin out which i did and i have it correct it also says something about swim power off and on..... i know the stlink works i flashed the dash with it so any ideas would be Awesome.
Error message https://imgur.com/gallery/uOnOMKJ
My BMS looks slightly different then op one but was told it is still done the same way but for dub measures here is pic of it
G30 max BMS https://imgur.com/gallery/IGoWefb
Error message https://imgur.com/gallery/uOnOMKJ
My BMS looks slightly different then op one but was told it is still done the same way but for dub measures here is pic of it
G30 max BMS https://imgur.com/gallery/IGoWefb
Re: [Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
Okay i figured it out the bms had to have the 2 plugs removed to cut power and comnected to stlink without issues.
Last edited by Christree on Thu Mar 04, 2021 12:40 am, edited 1 time in total.
Re: [Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
I was able to flash the dash but for some reason i cant seem to connect to the bms it says check swim cable and pin out which i did and i have it correct it also says something about swim power off and on..... i know the stlink works i flashed the dash with it so any ideas would be Awesome.
Error message https://imgur.com/gallery/uOnOMKJ
My BMS looks slightly different then op one but was told it is still done the same way but for dub measures here is pic of it
G30 max BMS https://imgur.com/gallery/IGoWefb
Okay i figured it out the bms had to have the 2 plugs removed to cut power and comnected to stlink without issues.
Re: [Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
The Dashboard I have looks the same but has different color wires from the bottom connector. can't seem to find a picture of the back side of the G30 dashboard used in the tutorial so I can figure out the order the wires attach to the connector.
When holding it vertically and looking at the back the connector is at the bottom and the colors from left to right are ORANGE YELLOW BLACK BLUE...
best guess I can make from a picture of the front is that it is BLACK YELLOW GREEN RED
any ideas?
thanks!
When holding it vertically and looking at the back the connector is at the bottom and the colors from left to right are ORANGE YELLOW BLACK BLUE...
best guess I can make from a picture of the front is that it is BLACK YELLOW GREEN RED
any ideas?
thanks!
Re: [Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
I am having the same problem. Which plugs did you remove?Okay i figured it out the bms had to have the 2 plugs removed to cut power and comnected to stlink without issues.
Re: [Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
The flash_BLE555.bat will not work as is!
You have to change the line so it reads like this:
bin\openocd.exe -f share\openocd\scripts\interface\stlink-v2.cfg -f share\openocd\scripts\target\nrf51.cfg -c init -c halt -c "nrf51 mass_erase" -c "program full_BLE555_upd7.1.bin" -c "program UICR 0x10001000 verify" -c "reset" -c "exit"
Currently it is missing the word "program" which causes it to fail! This will also prevent your dashboard from powering on if you try to flash with the incorrect command. I was able to redo the flash and it worked after I made the change.
You have to change the line so it reads like this:
bin\openocd.exe -f share\openocd\scripts\interface\stlink-v2.cfg -f share\openocd\scripts\target\nrf51.cfg -c init -c halt -c "nrf51 mass_erase" -c "program full_BLE555_upd7.1.bin" -c "program UICR 0x10001000 verify" -c "reset" -c "exit"
Currently it is missing the word "program" which causes it to fail! This will also prevent your dashboard from powering on if you try to flash with the incorrect command. I was able to redo the flash and it worked after I made the change.
Re: [Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
FYI also the 555- while it does flash and seems to work- does not allow me to flash anything with xiaoflasher. I reflashed the dash with flash_BLE110.bat and this works great and allows flashing over bluetooth.
Re: [Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
Is there any way to flash ble via stlink and otg cable with android? Sorry for stupid question, but I am trying to convert ex rental spin model, but no access to computer. I do however have stlink and a serial link
Re: [Full Tutorial] How to convert a Ninebot Max (G30) for Personal Use (ESC/BMS/BLE Flashing, Rewiring, and CFW)
Is there any way to flash ble via stlink and otg cable with android? Sorry for stupid question, but I am trying to convert ex rental spin model, but no access to computer. I do however have stlink and a serial link
Who is online
Users browsing this forum: mhz and 21 guests